Part Number Hot Search : 
MSS6132 CO4710 G1017 HC4024 BYV26D MTU429B SR400C SL210A
Product Description
Full Text Search
 

To Download TDA3604Q Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 INTEGRATED CIRCUITS
DATA SHEET
TDA3604Q; TDA3604TH Multiple voltage regulators with external reset delay and switch
Product specification Supersedes data of 1997 Aug 15 File under Integrated Circuits, IC01 1997 Aug 21
Philips Semiconductors
Product specification
Multiple voltage regulators with external reset delay and switch
FEATURES General * One VP-state controlled regulator (regulator 2) * Regulator 2, reset and ignition buffer operate during load dump and thermal shutdown * Separate control pins for switching regulator 1 and the power switch * Supply voltage range of -18 to +50 V (operating from 9.75 V) * Low reverse current of regulator 2 * Low quiescent current (when regulator 1, power switch and ignition buffer are switched off) * Ignition input/output * Reset output * Adjustable reset delay time * High ripple rejection * Power switch * Separate supply for the power switch. Protections * Reverse polarity safe (down to -18 V without high reverse current) * Able to withstand voltages up to 18 V at the outputs (supply line may be short-circuited) * ESD protected on all pins * Thermal protection * Load dump protection * Foldback current limit protection for regulators 1 and 2 * Delayed second current limit protection for the power switch * The regulator outputs and the power switch are DC short-circuited safe to ground and VP. ORDERING INFORMATION TYPE NUMBER TDA3604Q TDA3604TH PACKAGE NAME DESCRIPTION GENERAL DESCRIPTION
TDA3604Q; TDA3604TH
The TDA3604Q and TDA3604TH are multiple output voltage regulators with a power switch, intended for use in car radios with or without a microcontroller. It contains one fixed voltage regulator with a foldback current protection (regulator 1) and one fixed voltage regulator (regulator 2), intended to supply a microcontroller, that also operates during load dump and thermal shutdown. There is a power switch with protections, operated by an enable input. The reset and ignition outputs can be used to interface by the microcontroller. The reset signal can be used to call up the microcontroller and the ignition output indicates ignition voltage available. Both supply pins can withstand load dump pulses and negative supply voltages. Regulator 2 will be switched on at a supply voltage >6.5 V and off at a voltage of regulator 2 <1.9 V.
VERSION SOT141-6 SOT418-2
DBS13P plastic DIL-bent-SIL power package; 13 leads (lead length 12 mm) HSOP20 plastic heat-dissipating small outline package; 20 leads; low stand-off
1997 Aug 21
2
Philips Semiconductors
Product specification
Multiple voltage regulators with external reset delay and switch
QUICK REFERENCE DATA SYMBOL Supply VP supply voltage operating regulator 2 on jump start load dump protection Iq Tvj total quiescent current operating virtual junction temperature 0.5 mA IREG1 300 mA note 1 t 10 minutes during 50 ms; tr 2.5 ms standby mode PARAMETER CONDITIONS
TDA3604Q; TDA3604TH
MIN.
TYP.
MAX.
UNIT
9.75 2.4 - - - -
14.4 14.4 - - 400 -
25 25 30 50 500 150
V V V V A C
Voltage regulators VREG1 VREG2 VREGd1 Vswd IswM Notes 1. Minimum operating voltage, only if VP has exceeded 6.5 V. 2. The drop-out voltage of regulator 1 is measured between VP and VREG1. 3. The drop-out voltage of the power switch is measured between VI(sw) and VO(sw). output voltage regulator 1 output voltage regulator 2 drop-out voltage regulator 1 8.65 4.8 - - 1.4 9.0 5.0 - - - 9.35 5.2 0.5 V V V 0.5 mA IREG2 50 mA; VP = 14.4 V IREG1 = 0.3 A; note 2 Isw = 0.5 A; note 3 t 10 ms
Power switch drop-out voltage peak current 1.4 - V A
1997 Aug 21
3
Philips Semiconductors
Product specification
Multiple voltage regulators with external reset delay and switch
BLOCK DIAGRAM
TDA3604Q; TDA3604TH
handbook, full pagewidth
VI(sw) (14.4 V)
2
POWER SWITCH
13
VO(sw) (13.6 V/0.5 A)
Ven(sw)
7
&
TEMPERATURE LOAD DUMP PROTECTION
REGULATOR 2
11
REG2 (5 V/50 mA)
3 VP
&
6 Ven(REG1)
REGULATOR 1
4
REG1 (9 V/300 mA)
TDA3604Q
5
RES (5 V)
CRES VI(ig)
9 12 IGNITION BUFFER 10 ground
MBE237
8
VO(ig)
Fig.1 Block diagram (for DBS13P package; SOT141-6).
1997 Aug 21
4
Philips Semiconductors
Product specification
Multiple voltage regulators with external reset delay and switch
PINNING PIN SYMBOL SOT141-6 n.c. VI(sw) VP REG1 RES Ven(REG1) Ven(sw) VO(ig) CRES GND REG2 VI(ig) VO(sw) 1 2 3 4 5 6 7 8 9 10 11 12 13 SOT418-2
TDA3604Q; TDA3604TH
DESCRIPTION 1, 2, 6, 9, 13, 18, 19 and 20 not connected 3 4 5 7 8 10 11 12 14 15 16 17 power switch input supply voltage regulator 1 output reset output (+5 V) regulator 1 enable input power switch enable input ignition output reset delay capacitor ground (0 V) regulator 2 output ignition input power switch output
handbook, halfpage
n.c. Vl(sw) VP REG1 RES V en(REG1) Ven(sw) V O(ig) C RES GND REG2 V I(ig) V O(sw)
1 2 3 4 5 6 7 8 9 10 11 12 13
MBE236
handbook, halfpage
n.c. 20 n.c. 19 n.c. 18 VO(sw) 17 VI(ig) 16
1 n.c. 2 n.c. 3 VI(sw) 4 VP
5 REG1
TDA3604Q
TDA3604TH
REG2 15 GND 14 n.c. 13 CRES 12 VO(ig) 11
MGK596
6 7 8 9
n.c. RES Ven(REG1) n.c.
10 Ven(sw)
Fig.2 Pin configuration SOT141-6.
Fig.3 Pin configuration SOT418-2.
1997 Aug 21
5
Philips Semiconductors
Product specification
Multiple voltage regulators with external reset delay and switch
FUNCTIONAL DESCRIPTION The TDA3604Q and TDA3604TH are multiple output voltage regulators with a power switch, intended for use in car radios with or without a microcontroller. Because of low-voltage operation of the car radio, low-voltage drop regulators are used. Regulator 2 will switch on when the supply voltage exceeds 6.5 V for the first time and will switch off again when the output voltage of regulator 2 drops below 1.9 V (this is below an engine start). When regulator 2 is switched on and the output voltage of this regulator is within its voltage range, the reset output will be enabled (reset will go HIGH via a pull-up resistor) to generate a reset to the microcontroller. The reset cycles can be extended by an external capacitor at CRES (pin of the reset delay capacitor). The above mentioned start-up feature is built-in to secure a smooth start-up of the microcontroller at first connection, without uncontrolled switching of regulator 2 during the start-up sequence.
TDA3604Q; TDA3604TH
When both regulator 2 and the supply voltage (VP > 4.5 V) are available, regulator 1 and the power switch can be operated by the enable inputs Ven(REG1) and Ven(sw) respectively. All output pins are fully protected. The regulators are protected against load dump (regulator 1 will switch off at supply voltages higher than 25 V) and short-circuit (foldback current protection). The power switch contains a current protection which is delayed for 10 ms (in short-circuit condition). During this time the current is limited to 1.4 A (VP 18 V). At supply voltages over 16.9 V the power switch is clamped at 15.0 V (to avoid externally connected circuitry being damaged by an overvoltage) and the power switch will switch off at load dump. Interfacing with the microcontroller can be accomplished by an ignition Schmitt trigger and ignition output buffer, (simple full/semi on/off logic applications). The total timing of a semi on/off logic set is shown in Fig.4.
1997 Aug 21
6
Philips Semiconductors
Product specification
Multiple voltage regulators with external reset delay and switch
TDA3604Q; TDA3604TH
handbook, full pagewidth
load dump
VP
6.5 V 5.4 V 4.0 V 5.0 V 1.9 V 0V 5.0 V 0V
regulator 2
reset
load dump
18.0 V 8.9 V 4.5 V 4.0 V 2.2 V 2.0 V 8.5 V
VP
enable regulator 1
regulator 1
0V
ignition input
5.4 V 2.2 V 2.0 V 5.0 V 0.2 V
ignition output
load dump
16.9 V
VP
4.5 V 4.0 V
enable power switch
2.2 V 2.0 V
power switch output
0V
MBE235
Fig.4 Timing diagrams.
1997 Aug 21
7
Philips Semiconductors
Product specification
Multiple voltage regulators with external reset delay and switch
LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 134). SYMBOL VP supply voltage operating reverse polarity jump start load dump protection Vppi Vnpi Tstg Tvj Ptot positive pulse voltage at ignition buffer negative pulse voltage at ignition buffer storage temperature operating virtual junction temperature total power dissipation non-operating t 10 minutes PARAMETER
TDA3604Q; TDA3604TH
CONDITIONS - - - - - -
MIN.
MAX. 25 -18 30 50 50 -100 +150 +150 15.6 V V V V V V
UNIT
during 50 ms; tr 2.5 ms VP = 14.4 V; RI = 1 k VP = 14.4 V; RI = 1 k non-operating
-55 -40 -
C C W
THERMAL CHARACTERISTICS SYMBOL Rth j-c Rth j-a PARAMETER thermal resistance from junction to case thermal resistance from junction to ambient in free air VALUE 8 50 UNIT K/W K/W
1997 Aug 21
8
Philips Semiconductors
Product specification
Multiple voltage regulators with external reset delay and switch
CHARACTERISTICS VP = VI(sw) = 14.4 V; Tamb = 25 C; see Fig.7; unless otherwise specified. SYMBOL Supply VP supply voltage operating regulator 2 on jump start load dump protection Iq quiescent supply current note 1 t 10 minutes during 50 ms; tr 2.5 ms VP = 12.4 V; note 2 VP = 14.4 V; note 2 Schmitt trigger power supply for the power switch Vthr Vthf Vhys Vthr Vthf Vhys Vthr Vthf Vhys Vthr Vthf Vhys Vr(REG2) Vf(REG2) Vspread Vthr Vthf Vhys Isink Ileak rising threshold voltage falling threshold voltage hysteresis voltage PARAMETER CONDITIONS
TDA3604Q; TDA3604TH
MIN.
TYP.
MAX.
UNIT
9.75 2.4 - - - -
14.4 14.4 - - 400 420
25 25 30 50 500 -
V V V V A A
4.0 3.5 -
4.5 4.0 0.5
5.0 4.5 -
V V V
Schmitt trigger power supply for regulator 1 rising threshold voltage falling threshold voltage hysteresis voltage 4.0 3.5 - 4.5 4.0 0.5 5.0 4.5 - V V V
Schmitt trigger for regulator 2 rising threshold voltage falling threshold voltage hysteresis voltage 6.0 1.7 - 6.5 1.9 4.7 7.1 2.2 - V V V
Schmitt trigger for enable input (of regulator 1 and power switch) rising threshold voltage falling threshold voltage hysteresis voltage 1.7 1.5 - - - - 2.2 2.0 0.2 2.7 2.5 - V V V
Schmitt trigger for reset buffer rising voltage of regulator 2 falling voltage of regulator 2 voltage spread on tracking note 3 note 3 note 4 VREG2 - 0.15 - VREG2 - 0.25 - 10 - V V mV
Schmitt trigger for ignition buffer rising threshold voltage falling threshold voltage hysteresis voltage VRES 0.8 V VP = 14.4 V; VRES = 5 V 1.7 1.5 - 2.2 2.0 0.2 2.7 2.5 - - 100 V V V
Reset buffer LOW-level sink current leakage current 15 25 20 50 mA A
1997 Aug 21
9
Philips Semiconductors
Product specification
Multiple voltage regulators with external reset delay and switch
SYMBOL Ignition buffer VOL VOH IOL IOH VREG1 VREG1 VREG1 VREGL1 SVRR1 VREGd1 IREGm1 IREGsc1 ct VREG2 LOW-level output voltage HIGH-level output voltage LOW-level output current HIGH-level output current IOL = 0 note 5 VOL 0.8 V VOH 3 V PARAMETER CONDITIONS
TDA3604Q; TDA3604TH
MIN.
TYP.
MAX.
UNIT
0 - 0.3 0.3 -
0.2 5.0 0.8 2.0
0.8 5.2 - -
V V mA mA
Regulator 1; note 6 output voltage off output voltage line regulation load regulation supply voltage ripple rejection drop-out voltage current limit short-circuit current cross talk 0.5 mA IREG1 300 mA 10 V VP 18 V 10 V VP 18 V 0.5 mA IREG1 300 mA fi = 200 Hz; VI = 2 V (p-p) IREG1 = 300 mA; note 7 VREG1 > 7 V; note 8 RL 0.5 ; note 9 note 10 0.5 mA IREG2 50 mA 7 V VP 18 V 18 V VP 50 V VREG2 VREGL2 SVRR2 VREGd2 IREGm2 IREGsc2 ct Vswd Iswcc Vswcl IswM Vswfb Ilim(sw) line regulation load regulation supply voltage ripple rejection drop-out voltage current limit short-circuit current cross talk 7 V VP 18 V 0.5 mA IREG1 30 mA fi = 200 Hz; VI = 2 V (p-p) IREG2 = 30 mA; note 12 VREG2 > 4.5 V; note 8 RL 0.5 ; note 9 note 13 1 9.0 9.0 - - - 0.4 - 300 50 400 9.35 9.35 50 70 - 0.5 1.2 - - mV V V mV mV dB V A mA dB 8.65 8.65 - - 60 - 0.45 50 -
Regulator 2; note 11 output voltage 4.8 4.8 4.75 - - 60 - 0.1 20 - - 0.5 VP 16.9 V t 10 ms Isw = -200 mA; VP = 9 V VP = 14.4 V; Vsw < 1.5 V; note 8 - 1.4 - 0.6 5.0 5.0 5.0 - - - 0.3 - 50 50 5.2 5.2 5.25 50 50 - 0.4 0.5 - - V V V mV mV dB V A mA dB
Power switch drop-out voltage continuous current clamping voltage peak current fly back voltage behaviour current limit Isw = 0.5 A; note 14 0.8 - 15.0 - - 0.9 1.4 - 16.2 - 20 - V A V A V A
Reset delay IO Vthr td output current rising threshold voltage delay time CI = 47 nF; note 15 - 2.7 25 3 3.0 50 - 3.3 100 A V ms
1997 Aug 21
10
Philips Semiconductors
Product specification
Multiple voltage regulators with external reset delay and switch
Notes to the characteristics 1. Minimum operating voltage, only if VP has exceeded 6.5 V.
TDA3604Q; TDA3604TH
2. Enable inputs of regulator 1, ignition and power switch are low. Regulator 2 is unloaded. 3. Voltage drop due to load condition. 4. The spread on tracking is one sigma value. 5. Ignition output voltage will be less than or equal to the output voltage of regulator 2. 6. IREG1 = 5 mA unless otherwise specified. 7. The drop-out voltage of regulator 1 is measured between VP and VREG1. 8. At current limit, IREGm is held constant (see Fig.5). 9. The foldback current protection limits the dissipated power at short-circuit (see Figs 5 and 6). 10. The cross talk of regulator 1 is measured with an IREG2 = 0.5 mA up to 30 mA and input frequency of fi = 100 kHz. 11. IREG2 = 5 mA unless otherwise specified. 12. The drop-out voltage of regulator 2 is measured between VP and VREG2. 13. The cross talk of regulator 2 is measured with an IREG1 = 0.5 mA up to 100 mA and input frequency of fi = 100 kHz. 14. The drop-out voltage of the power switch is measured between VI(sw) and VO(sw).
6 C 15. The delay time depends on the value of the capacitor: t d = --- x V thrC = C x 2.5 x 10 I
1997 Aug 21
11
Philips Semiconductors
Product specification
Multiple voltage regulators with external reset delay and switch
TDA3604Q; TDA3604TH
handbook, halfpage
MBE233
Rx
V0 (regulators 1 and 2)
V0 I sc Im I o (regulators 1 and 2)
Fig.5 Foldback current protection of the regulators.
handbook, halfpage
MBE234
1.4 1.4 I sw (A) 0.5 t (ms)
10
Fig.6 Foldback current protection of the power switch.
1997 Aug 21
12
Philips Semiconductors
Product specification
Multiple voltage regulators with external reset delay and switch
TEST AND APPLICATION INFORMATION
TDA3604Q; TDA3604TH
handbook, full pagewidth
power switch input C1 (1) 220 nF power switch enable input
2
13
power switch output C2 10 F regulator 2 output 5V C3 10 F regulator 1 output 47 k R2 reset output 8.5 V C4 10 F R L(REG1) 1 k R L(REG2) 1 k R L(sw) 1 k
V l(sw) R1 Ven(sw) 1 k
7
11
supply voltage VP R3 Ven(REG1) 1 k reset delay capacitor C7 47 nF VI(ig) ignition input C5 220 nF regulator 1 enable input
(1)
3
TDA3604Q
4
6 9 12 10 ground
5 C5 1 F ignition output
MBE238
8
(1) Capacitor not required for stability.
Fig.7 Test circuit (for DBS13P package; SOT141-6).
Noise information The noise at the output of the regulators depends on the bandwidth of the regulators, which can be adjusted by the output capacitors. Table 1 shows the noise figures. Although stability is guaranteed when CL is higher than 10 F (over temperature range) with tan () = 1 in the frequency range 1 to 10 kHz, however, for low noise, a 47 F load capacitor is required. The noise on the supply line depends on the value of the supply capacitor and is caused by a current noise (output noise of the regulators is translated into a current noise by the output capacitors). When a high frequency capacitor of 220 nF with an electrolytic capacitor of 100 F in parallel is placed directly over VP and GND (pins of supply voltage and ground) the noise is minimized.
Table 1
Noise figures NOISE (V)(1) 180 OUTPUT CAPACITOR (F) 10 47 100 10 47 100
REGULATOR
1
100 80 120
2
70 70
Note 1. Bandwidth of 100 kHz.
1997 Aug 21
13
Philips Semiconductors
Product specification
Multiple voltage regulators with external reset delay and switch
SHORT CIRCUIT BEHAVIOUR OF POWER SWITCH The short circuit behaviour of the switch with large inductive loads (switch output goes out of the radio) can be improved by replacing C2 (see Fig.7) by a larger electrolytic capacitor of 10 F/16 V. When the temperature protection of the switch becomes active, due to a short circuit of the switch, the behaviour will be improved. When the switch is clamped an minimum output capacitor of 10 F is needed. The power switch is not protected against `loss of ground' condition (= short of the switch to ground with floating ground pin of the TDA3604 itself). A `loss of ground' situation can in practice only occur when the switch output goes outside the car-radio box.
TDA3604Q; TDA3604TH
There is an application solution to protect against `loss of ground' (see Fig.8). It is advisable to limit the dissipation at short circuit condition by monitoring the output of the power switch. The microprocessor can switch of the power switch when the switch was enabled and the switch output remains low due to a short circuit condition.
handbook, full pagewidth
Vbat (+)
VI(sw), VP
2, 3
13
VO(sw)
D1 switch output
TDA3604Q
D3 10 GND radio disconnected from Vbat (-)
MGL209
C1 D2 short circuit to Vbat (-) Vbat (-)
Vbat (-)
Fig.8 `Loss of ground' protection.
1997 Aug 21
14
Philips Semiconductors
Product specification
Multiple voltage regulators with external reset delay and switch
PACKAGE OUTLINES
TDA3604Q; TDA3604TH
DBS13P: plastic DIL-bent-SIL power package; 13 leads (lead length 12 mm)
SOT141-6
non-concave x D Dh
Eh
view B: mounting base side
d
A2
B j E A
L3
L
Q c
1 Z e e1 bp wM
13 m e2 vM
0
5 scale
10 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A 17.0 15.5 A2 4.6 4.2 bp 0.75 0.60 c 0.48 0.38 D (1) 24.0 23.6 d 20.0 19.6 Dh 10 E (1) 12.2 11.8 e 3.4 e1 1.7 e2 5.08 Eh 6 j 3.4 3.1 L 12.4 11.0 L3 2.4 1.6 m 4.3 Q 2.1 1.8 v 0.8 w 0.25 x 0.03 Z (1) 2.00 1.45
Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT141-6 REFERENCES IEC JEDEC EIAJ EUROPEAN PROJECTION
ISSUE DATE 92-11-17 95-03-11
1997 Aug 21
15
Philips Semiconductors
Product specification
Multiple voltage regulators with external reset delay and switch
TDA3604Q; TDA3604TH
HSOP20: plastic heat-dissipating small outline package; 20 leads; low stand-off
SOT418-2
E D x
A X
c y HE vM A
D1 Z 1 pin 1 index Q A2 E2 E1 A4 Lp detail X 20 bp 11 wM (A3) A 10 D2
e
0
5 scale
10 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A A2 max. 3.4 3.4 3.1 A3 0.35 A4 bp c D(1) D1 D2 1.1 0.9 E(1) 11.1 10.9 E1 6.2 5.8 E2 2.9 2.5 e 1.27 HE 14.5 13.9 Lp 1.1 0.8 Q 1.7 1.5 v w x y Z 2.5 2.0 8 0
+0.13 0.53 0.32 16.0 13.0 -0.04 0.40 0.23 15.8 12.6
0.25 0.25 0.03 0.07
Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT418-2 REFERENCES IEC JEDEC EIAJ EUROPEAN PROJECTION
ISSUE DATE 96-11-18
1997 Aug 21
16
Philips Semiconductors
Product specification
Multiple voltage regulators with external reset delay and switch
SOLDERING Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often used. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our "IC Package Databook" (order code 9398 652 90011). DBS SOLDERING BY DIPPING OR BY WAVE The maximum permissible temperature of the solder is 260 C; solder at this temperature must not be in contact with the joint for more than 5 seconds. The total contact DEFINITIONS Data sheet status Objective specification Preliminary specification Product specification Limiting values
TDA3604Q; TDA3604TH
time of successive solder waves must not exceed 5 seconds. The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified maximum storage temperature (Tstg max). If the printed-circuit board has been pre-heated, forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit. REPAIRING SOLDERED JOINTS Apply a low voltage soldering iron (less than 24 V) to the lead(s) of the package, below the seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is less than 300 C it may remain in contact for up to 10 seconds. If the bit temperature is between 300 and 400 C, contact may be up to 5 seconds. HSOP No information available at the moment.
This data sheet contains target or goal specifications for product development. This data sheet contains preliminary data; supplementary data may be published later. This data sheet contains final product specifications.
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale.
1997 Aug 21
17
Philips Semiconductors
Product specification
Multiple voltage regulators with external reset delay and switch
NOTES
TDA3604Q; TDA3604TH
1997 Aug 21
18
Philips Semiconductors
Product specification
Multiple voltage regulators with external reset delay and switch
NOTES
TDA3604Q; TDA3604TH
1997 Aug 21
19
Philips Semiconductors - a worldwide company
Argentina: see South America Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113, Tel. +61 2 9805 4455, Fax. +61 2 9805 4466 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. +43 160 1010, Fax. +43 160 101 1210 Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6, 220050 MINSK, Tel. +375 172 200 733, Fax. +375 172 200 773 Belgium: see The Netherlands Brazil: see South America Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor, 51 James Bourchier Blvd., 1407 SOFIA, Tel. +359 2 689 211, Fax. +359 2 689 102 Canada: PHILIPS SEMICONDUCTORS/COMPONENTS, Tel. +1 800 234 7381 China/Hong Kong: 501 Hong Kong Industrial Technology Centre, 72 Tat Chee Avenue, Kowloon Tong, HONG KONG, Tel. +852 2319 7888, Fax. +852 2319 7700 Colombia: see South America Czech Republic: see Austria Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S, Tel. +45 32 88 2636, Fax. +45 31 57 0044 Finland: Sinikalliontie 3, FIN-02630 ESPOO, Tel. +358 9 615800, Fax. +358 9 61580920 France: 4 Rue du Port-aux-Vins, BP317, 92156 SURESNES Cedex, Tel. +33 1 40 99 6161, Fax. +33 1 40 99 6427 Germany: Hammerbrookstrae 69, D-20097 HAMBURG, Tel. +49 40 23 53 60, Fax. +49 40 23 536 300 Greece: No. 15, 25th March Street, GR 17778 TAVROS/ATHENS, Tel. +30 1 4894 339/239, Fax. +30 1 4814 240 Hungary: see Austria India: Philips INDIA Ltd, Band Box Building, 2nd floor, 254-D, Dr. Annie Besant Road, Worli, MUMBAI 400 025, Tel. +91 22 493 8541, Fax. +91 22 493 0966 Indonesia: see Singapore Ireland: Newstead, Clonskeagh, DUBLIN 14, Tel. +353 1 7640 000, Fax. +353 1 7640 200 Israel: RAPAC Electronics, 7 Kehilat Saloniki St, PO Box 18053, TEL AVIV 61180, Tel. +972 3 645 0444, Fax. +972 3 649 1007 Italy: PHILIPS SEMICONDUCTORS, Piazza IV Novembre 3, 20124 MILANO, Tel. +39 2 6752 2531, Fax. +39 2 6752 2557 Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108, Tel. +81 3 3740 5130, Fax. +81 3 3740 5077 Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL, Tel. +82 2 709 1412, Fax. +82 2 709 1415 Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR, Tel. +60 3 750 5214, Fax. +60 3 757 4880 Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905, Tel. +9-5 800 234 7381 Middle East: see Italy Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB, Tel. +31 40 27 82785, Fax. +31 40 27 88399 New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND, Tel. +64 9 849 4160, Fax. +64 9 849 7811 Norway: Box 1, Manglerud 0612, OSLO, Tel. +47 22 74 8000, Fax. +47 22 74 8341 Philippines: Philips Semiconductors Philippines Inc., 106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI, Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474 Poland: Ul. Lukiska 10, PL 04-123 WARSZAWA, Tel. +48 22 612 2831, Fax. +48 22 612 2327 Portugal: see Spain Romania: see Italy Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW, Tel. +7 095 755 6918, Fax. +7 095 755 6919 Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231, Tel. +65 350 2538, Fax. +65 251 6500 Slovakia: see Austria Slovenia: see Italy South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale, 2092 JOHANNESBURG, P.O. Box 7430 Johannesburg 2000, Tel. +27 11 470 5911, Fax. +27 11 470 5494 South America: Rua do Rocio 220, 5th floor, Suite 51, 04552-903 Sao Paulo, SAO PAULO - SP, Brazil, Tel. +55 11 821 2333, Fax. +55 11 829 1849 Spain: Balmes 22, 08007 BARCELONA, Tel. +34 3 301 6312, Fax. +34 3 301 4107 Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM, Tel. +46 8 632 2000, Fax. +46 8 632 2745 Switzerland: Allmendstrasse 140, CH-8027 ZURICH, Tel. +41 1 488 2686, Fax. +41 1 481 7730 Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1, TAIPEI, Taiwan Tel. +886 2 2134 2865, Fax. +886 2 2134 2874 Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd., 209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260, Tel. +66 2 745 4090, Fax. +66 2 398 0793 Turkey: Talatpasa Cad. No. 5, 80640 GULTEPE/ISTANBUL, Tel. +90 212 279 2770, Fax. +90 212 282 6707 Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7, 252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461 United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes, MIDDLESEX UB3 5BX, Tel. +44 181 730 5000, Fax. +44 181 754 8421 United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409, Tel. +1 800 234 7381 Uruguay: see South America Vietnam: see Singapore Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD, Tel. +381 11 625 344, Fax.+381 11 635 777
For all other countries apply to: Philips Semiconductors, Marketing & Sales Communications, Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825 (c) Philips Electronics N.V. 1997
Internet: http://www.semiconductors.philips.com
SCA55
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
547027/1200/04/pp20
Date of release: 1997 Aug 21
Document order number:
9397 750 02741


▲Up To Search▲   

 
Price & Availability of TDA3604Q

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X